View OPL535-OCB_349041.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Photologic Sensor
OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563
Features:
* * * * * *
Choice of four output options in low-cost side-looking package Choice of two sensitivity options (OPL560/561/562/563) High noise immunity Direct TTL/LSTTL CMOS interface Data rates to 250 kBaud for all except OPL560 series (200 kBaud) Low power consumption
Product Photo Here
Description:
All components in this series include a photodiode, amplifier, voltage regulator, Schmitt trigger and NPN output transistor on a single silicon chip. OPL560 chips also include a voltage regulator on the chip. All devices in the series have a Photologic(R) chip that is encapsulated in a molded plastic side-looking package with an integral lens (recessed integral lens for OPL535 and OPL536). This packaging provides enhanced optical coupling, combined with mechanical protection. The hysteresis characteristics of the Schmitt trigger on each device offers high immunity to noise on input and VCC. OPL530, OPL531, OPL535 and OPL536 include a 10 K pull-up resistor (RL) from output to VCC. These components exhibit very stable performance over supply voltages ranging from 4.5 V to 16 V and a wide range of irradiance levels. OPL550 and OPL551 devices feature TTL/LSTTL compatible logic level output which can drive up to 8 TTL loads without additional circuitry and medium-speed data rates to 250 kBaud, with typical rise and fall times of 25 nanoseconds. OPL560, OPL561, OPL562 and OPL563 devices feature TTL/LSTTL compatible logic level output which can drive up to 10 TTL loads over supply voltages ranging from 4.5 V to 16 V. OPL530, OPL531, OPL550, OPL551, OPL560, OPL561, OPL562 and OPL563 are mechanically and spectrally matched to OP140 and OP240 LEDs. OPL535 and OPL536 are mechanically and spectrally matched to OP145 and OP245 series LEDs.
Applications:
* * * * * *
Non-contact reflective object sensor Assembly line automation Machine automation Machine safety End of travel sensor Door sensor
Base Part Number
OPL530 OPL531 OPL535 OPL536 OPL550 OPL551 OPL560 OPL561 OPL562 OPL563
Package
Output Type - with Light
Internal 10K - High Internal 10K - Low Internal 10K - High Internal 10K - Low
Input Power Range (mW/cm2) [Min/Max]
A B
0.08/.40
0.08/.25
Recessed Lens
Totem Pole - High Totem Pole - Low Totem Pole - High Totem Pole - Low Totem Pole - High Totem Pole - Low OC = Open Collector Output
0.25/2.4 0.25/2.5 0.09/.55
0.25/1.4 0.25/1.5 0.09/.36
0.20/0.40
0.025/.23
0.025/.14
RoHS
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A 09/08 Page 1 of 8
OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Photologic Sensor
OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563
OPL530, OPL550, OPL560 Series
DIMENSIONS ARE IN:
[ MILLIMETERS] INCHES
Pin #
1 2 3
Sensor
Ground Output VCC
OPL535, OPL536 Series
DIMENSIONS ARE IN:
[ MILLIMETERS] INCHES
Pin #
1 2 3
Sensor
Ground Output VCC
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A 09/08 Page 2 of 8 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Photologic Sensor
OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563
OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 (-OC, -OCA, -OCB) OPL550, OPL550A, OPL551, OPL551A, OPL560, OPL560A, OPL561, OPL561A, OPL562, OPL562A, OPL563, OPL563A
OPL550/550A/560/560A/562/562A Totem-Pole VCC OPL530/535/550/560/562 (-OC, -OCA, -OCB) Open-Collector VCC
OUT OUT
GND OPL 551/551A/561/561A/563/563A/ Inverted Totem-Pole VCC
GND
OPL 531/536/551/561/563 (-OC, -OCA, -OCB) Inverted Open-Collector VCC
OUT
OUT
GND
GND
OPL530, OPL530A, OPL530B, OPL531, OPL531A, OPL531B OPL535, OPL535A, OPL535B, OPL536, OPL536A, OPL536B
OPL530/530A/530B, OPL535/535A/535B 10K Pull-Up VCC OPL531/531A/531B, OPL536/536A/536B Inverted 10K Pull-Up VCC
OUT OUT
GND
GND
VCC
VCC
OUT OUT
GND
GND
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A 09/08 Page 3 of 8
Photologic Sensor
OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563
Absolute Maximum Ratings (TA=25C unless otherwise noted)
Input Diode Supply Voltage (VCC) OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536, OPL536-OC, OPL550, OPL551 OPL560, OPL561, OPL562, OPL563 Operating Temperature Range Storage Temperature Range Lead Soldering Temperature [1/16 inch (1.6mm) from the case for 5 sec. with soldering iron] Sourcing Current OPL560, OPL561, OPL562, OPL563 Power Dissipation OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536, OPL536-OC OPL550, OPL551, OPL560, OPL561, OPL562, OPL563 Sinking Current OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536, OPL536-OC OPL550, OPL551 OPL560, OPL561, OPL562, OPL563 Voltage at Output Lead (4) OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536, OPL536-OC OPL550-OC, OPL551-OC OPL560-OC, OPL561-OC, OPL562-OC, OPL563-OC Duration of Output Short to VCC or Ground OP550, OP551 Duration of Output Short to VCC OPL550-OC, OPL551-OC OPL560, OPL561, OPL562, OPL563, OPL560-OC, OPL561-OC, OPL562-OC, OPL563-OC Low Level Output Current OPL550, OPL551 Series High Level Output Current OPL550, OPL551 Series Irradiance OPL550, OPL551 Series OPL560, OPL560-OC, OPL561, OPL561-OC OPL562, OPL562-OC, OPL563, OPL563-OC 18 V 10 V 18 V -40 C to + 85 C -40 C to + 100 C 260C 10 mA 90 mW 200 mW(2) 50 mA 50 mA 35 V 35 V 35 V 1 second 1 second 1 second 16 mA 1 mA 10 mW/cm2 9 mW/cm 3 mW/cm2
Notes: (1) RMA flux is recommended. Duration can be extended to 10 sec. max. when flow soldering. For OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and OPL536-OC, a maximum of 20 grams force may be applied to leads while at soldering temperatures. (2) Derate linearly 2.67 mW/C above 70 C for OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and OPL536-OC. Derate linearly 2.5 mW/ C above 25 C for all devices in the OPL550, OPL551, OPL560, OPL561, OPL562 and OPL563 series. (3) Irradiance measurements are made with i = 935 nm. (4) This applies to OC versions only. For ICC on pull-up versions, add VCC/10 K.
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A 09/08 Page 4 of 8 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Photologic Sensor
OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563
Electrical Characteristics (TA = 25C unless otherwise noted)
SYMBOL PARAMETER Operating Supply Voltage
OPL530, OPL530-OC, OPL531, OPL531-OC OPL535, OPL535-OC, OPL536, OPL536-OC, OPL560, OPL561 Series OPL550, OPL551 Series
MIN 4.5 4.5
TYP MAX 16 5.5
UNITS V
TEST CONDITIONS -
V
VCC
Peak-to-Peak VCC Ripple Necessary to Cause False Triggering of Output
OPL530, OPL530-OC, OPL531, OPL531-OC
OPL535, OPL535-OC, OPL536, OPL536-OC OPL560, OPL561 Series OPL550, OPL551 Series
-
-
2
V
f = DC to 50 MHz
0.08 0.08 0.12 .25 .25 1.05 1.05 1.50
2 2.7 8 8 1.3 1.2 2
5 15 12 0.40 0.25 0.40 2.4 1.4 1.6 1.5 2.5 2 -
V mA mA mA
VCC = 5 V DC, f = DC to 50 MHz EE = 0 or 1 mW/cm2 EE = 0 or 3 mW/cm2, VCC = 5.5 V EE = 0 or 1 mW/cm2
Supply Current(4)
OPL530, OPL530-OC, OPL531, OPL531-OC OPL535, OPL535-OC, OPL536, OPL536-OC
ICC
OPL550, OPL551 Series
OPL560, OPL561 Series
Positive-Going Threshold Irradiance(3)
OPL530, OPL530-OC, OPL531, OPL531-OC OPL535, OPL535-OC, OPL536, OPL536-OC OPL530A, OPL530-OCA, OPL531A, OPL531-OCA OPL535A, OPL535-OCA, OPL536A, OPL536-OCA OPL530B, OPL530-OCB, OPL531B, OPL531-OCB OPL535B, OPL535-OCB, OPL536B, OPL536-OCB OPL550, OPL550-OC, OPL551, OPL551-OC OPL550A, OPL550-OCA, OPL551, OPL551-OCA
mW/cm2 TA = 25 C mW/cm2 TA = 25 C mW/cm2 TA = 25 C mW/cm2 VCC = 5 V, TA = 25 C mW/cm2 VCC = 5 V, TA = 25 C
EeT(+)
Hysteresis Ratio
OP530, OP531 Series OP535, OP536 Series OPL550, OPL551 Series OPL560, OPL561 Series
%/C %/C >0C <0C
-
EeT(+)/EeT(-)
1.20 1.55 -0.6 -1.6
Eet(+) (T)
Temperature Co-efficient
OPL530, OPL530-OC, OPL531, OPL531-OC OPL535, OPL535-OC, OPL536, OPL536-OC
Notes: (1) RMA flux is recommended. Duration can be extended to 10 sec. max. when flow soldering. For OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and OPL536-OC, a maximum of 20 grams force may be applied to leads while at soldering temperatures. (2) Derate linearly 2.67 mW/C above 70 C for OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and OPL536-OC. Derate linearly 2.5 mW/ C above 25 C for all devices in the OPL550, OPL551, OPL560, OPL561, OPL562 and OPL563 series. (3) Irradiance measurements are made with i = 935 nm. (4) This applies to OC versions only. For ICC on pull-up versions, add VCC/10 K.
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A 09/08 Page 5 of 8
Photologic Sensor
OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563
Electrical Characteristics (TA = 25C unless otherwise noted)
SYMBOL
OPL550
PARAMETER Operating Supply Voltage
OPL551 OPL560 OPL561
MIN 2.4 2.4
VCC -2.1 VCC -2.1
TYP MAX 3.3 3.3 0.2 0.2 0.25 0.25 -55 -55 0.4 0.4 0.4 0.4 .4 .4 -100 -100
UNITS V V V V V V V V V V mA mA
TEST CONDITIONS VCC = 4.5 V, IOH = -800 a, EE = 3 mW/cm2 VCC = 4.5 V, IOH = -800 a, EE = 0 IOH = -1 A, EE = 1 mW/cm2 IOH = -1 A, EE = 0 IOL = 16 mA, EE = 0 IOL = 16 mA, EE = 1 mW/cm2 VCC = 4.5 V, IOL = 12.8 mA, EE = 0 VCC = 4.5 V, IOL = 12.8 mA, EE = 3 mW/cm2 IOL = 16 mA, EE = 0 IOL = 16 mA, EE = 1 mW/cm2 VCC = 5.5 V, Output = GND, EE = 3 mW/cm2 VCC = 5.5 V, Output = GND, EE = 0 VOH = 30 V, EE = 0 VOH = 30 V, EE = 1 mW/cm2 VCC = 4.5 V, VOH = 30 V, EE = 3 mW/cm2 VCC = 4.5 V, VOH = 30 V, EE = 0 VOH = 30 V, EE = 1 mW/cm2 VOH = 30 V, EE = 0
VOH
Low Level Output Voltage
OPL530, OPL530-OC, OPL535, OPL535-OC OPL531, OPL531-OC, OPL536, OPL536-OC
-20 -20
VOL
OPL550 OPL551 OPL560, OPL560-OC OPL561, OPL561-OC
Short Circuit Output Current IOS
OPL550 OPL551
High Level Output Current(4)
OPL531, OPL531-OC, OPL536, OPL536-OC OPL535, OPL535-OC, OPL530, OPL530-OC
-
0.1 0.1 1 1 -
10 10 100 100 100 100
A A A A A A
IOH
OPL550-OC OPL551-OC OPL560-OC OPL561-OC
Notes: (1) RMA flux is recommended. Duration can be extended to 10 sec. max. when flow soldering. For OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and OPL536-OC, a maximum of 20 grams force may be applied to leads while at soldering temperatures. (2) Derate linearly 2.67 mW/C above 70 C for OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and OPL536-OC. Derate linearly 2.5 mW/ C above 25 C for all devices in the OPL550, OPL551, OPL560, OPL561, OPL562 and OPL563 series. (3) Irradiance measurements are made with i = 935 nm. (4) This applies to OC versions only. For ICC on pull-up versions, add VCC/10 K.
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A 09/08 Page 6 of 8 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Photologic Sensor
OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563
Electrical Characteristics (TA = 25C unless otherwise noted)
SYMBOL PARAMETER Output Rise Time
OPL530, OPL531, OPL535, OPL536 OPL530-OC, OPL531-OC, OPL535-OC, OPL536-OC OPL550, OPL551
MIN -
TYP MAX 1.5 50 25 25 25 70 70 70 100 -
UNITS s ns ns ns ns s
TEST CONDITIONS EE = 0 or 1 mW/cm2, CL = 50 pF EE = 0 or 1 mW/cm2, RL = 300 to 5 V, CL = 50 Pf VCC = 5 V, TA = 25 C, EE = 0 or 3 mW/cm2, f = 10 kHz, DC = 50% RL = 8 TTL loads VCC = 5 V, TA = 25 C, EE = 0 or 3 mW/cm2, f = 10 kHz, DC = 50%, RL = 360 TA = 25 C, EE = 0 or 1 mW/cm2, f = 10 kHz, DC = 50%, RL = 360 EE = 0 or 1 mW/cm2, CL = 50 pF EE = 0 or 1 mW/cm2, RL = 300 to 5 V, CL = 50 pF VCC = 5 V, TA = 25 C, EE = 0 or 3 mW/cm2, RL = 8 TTL loads, f = 10 kHz, DC = 50% VCC = 5 V, TA = 25 C, EE = 0 or 3 mW/cm2, RL = 8 TTL loads, f = 10 kHz, DC = 50% TA = 25 C, EE = 0 or 1 mW/cm2, f = 10 kHz TA = 25 C, EE = 0 or 1 mW/cm2, f = 10 kHz
tr
OPL550-OC, OPL551-OC
OPL560, OPL561 OPL560-OC, OPL561-OC
Output Rise Time
OPL530, OPL531, OPL535, OPL536 OPL530-OC, OPL531-OC, OPL535-OC, OPL536-OC OPL550-OC, OPL551-OC
s ns 70 70 70 100 ns ns ns ns
tr
OPL560-OC, OPL561-OC
OPL560, OPL561 OPL560-OC, OPL561-OC
Output Fall Time
OPL530, OPL531, OPL535, OPL536 OPL530-OC, OPL531-OC, OPL535-OC, OPL536-OC
-
20 20 25 -
70 70 100
ns ns ns ns ns
EE = 0 or 1 mW/cm2, CL = 50 Pf EE = 0 or 1 mW/cm2, RL = 300 to 5 V, CL = 50 pF VCC = 5 V, TA = 25 C, EE = 0 or 3 mW/cm2, RL = 360 , f = 10 kHz, DC = 50% TA = 25 C, EE = 0 or 1 mW/cm2, f = 10 kHz TA = 25 C, EE = 0 or 1 mW/cm2, f = 10 kHz
tf
OPL550-OC, OPL551-OC
OPL560, OPL561 OPL560-OC, OPL561-OC
Notes: (1) RMA flux is recommended. Duration can be extended to 10 sec. max. when flow soldering. For OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and OPL536-OC, a maximum of 20 grams force may be applied to leads while at soldering temperatures. (2) Derate linearly 2.67 mW/C above 70 C for OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and OPL536-OC. Derate linearly 2.5 mW/ C above 25 C for all devices in the OPL550, OPL551, OPL560, OPL561, OPL562 and OPL563 series. (3) Irradiance measurements are made with i = 935 nm. (4) This applies to OC versions only. For ICC on pull-up versions, add VCC/10 K.
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A 09/08 Page 7 of 8
Photologic Sensor
OPL530, OPL531, OPL535, OPL536, OPL550, OPL551, OPL560, OPL561, OPL562, OPL563
Electrical Characteristics (TA = 25C unless otherwise noted)
SYMBOL PARAMETER Propagation Delay
OPL530, OPL531, OPL535, OPL536
MIN
TYP MAX
UNITS
TEST CONDITIONS
-
1.0 1.0 2.5
5
s s s
tpEeT(+)
OPL530-OC, OPL531-OC, OPL535-OC, OPL536-OC OPL550-OC, OPL551-OC
EE = 0 or 1 mW/cm2, RL = 300 to 5 V, CL = 50 pF EE = 0 or 1 mW/cm2, RL = 300 to 5 V, CL = 50 pF VCC = 5 V, TA = 25 C, EE = 0 or 3 mW/cm2, RL = 8 TTL loads, f = 10 kHz, DC = 50% EE= 0 or 1 mW/cm2, RL = 300 to 5V, CL = 50 pF VCC = 5 V, TA = 25 C, EE = 0 or 3 mW/cm2, RL = 360 , f = 10 kHz, DC = 50%
Propagation Delay
OPL530, OPL531, OPL535, OPL536, OPL530-OC, OPL531-OC, OPL535-OC, OPL536-OC OPL550-OC, OPL551-OC
-
3.0 2.5
5
s s
tpEeT(-)
Propagation Delay (Low-High/High-Low) tPLH, TPHL
OPL560, OPL561 OP560-OC, OPL561-OC
-
5 5
-
s s
DC = 50%, RL = 10 TTL Loads DC = 50%, RL = 300
Notes: (1) RMA flux is recommended. Duration can be extended to 10 sec. max. when flow soldering. For OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and OPL536-OC, a maximum of 20 grams force may be applied to leads while at soldering temperatures. (2) Derate linearly 2.67 mW/C above 70 C for OPL530, OPL530-OC, OPL531, OPL531-OC, OPL535, OPL535-OC, OPL536 and OPL536-OC. Derate linearly 2.5 mW/ C above 25 C for all devices in the OPL550, OPL551, OPL560, OPL561, OPL562 and OPL563 series. (3) Irradiance measurements are made with i = 935 nm. (4) This applies to OC versions only. For ICC on pull-up versions, add VCC/10 K.
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A 09/08 Page 8 of 8 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com

▲Up To Search▲

Price & Availability of OPL535-OCB

	To Download OPL535-OCB Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .